當前位置:首頁 - 新聞動態 > 企業動態 >

數控彈簧機轉動部分的日常的維護特點

來源:http://www.diannaothj.com   時間:2017-04-11 18:47:38作者:山東銀豐彈簧機設備

 壹、關閉數控彈簧機電源,等待五分鐘讓循環機油流回儲油槽。找壹接油盤,置於潤滑泵之下方,緩慢缷下缷油塞,讓油流到接油盤裏。(註意:不要壹下子拿掉缷油塞,以防油從缷油口沖出流到地面。),放置支撐架於儲油槽底下。
Turn off the power of the CNC spring machine, wait for five minutes to let the circulating oil return to the oil storage tank. Find a pan, under a lubrication pump unloading, slowly lowering plug, let the oil flow to drip pan. (Note: do not suddenly take off oil plug, to prevent the oil from the oil inlet flow to the ground rushed off. The support frame is placed under the oil storage tank.
二、放松潤滑泵固定螺絲,取下潤滑泵,松開儲油槽上方螺絲,取下儲油槽並清洗。在這操作中有以下幾點需要註意:
Two, loosen the lubrication pump fixed screw, remove the lubrication pump, loosen the oil tank above the screw, remove the oil tank and clean. In this operation, the following points need to be noted:
1、請將儲油槽底下放置同高的支撐架,避免在進行拆裝動作時,不慎將潤滑泵摔壞等壹些意外事故放生。
1, please put the oil tank under the same height of the support frame, in order to avoid disassembly and assembly operations, the pump will be accidentally broken and other accidents.
2、取下潤滑泵時,請註意供油馬達電源線,請勿做強行拉扯或試圖取下線頭之動作。
2, take off the lubrication pump, please pay attention to the oil supply motor power cord, do not pull or try to pull the pull off the head of the action.
三、清洗吸油口處過濾網,清除附著在過濾網上的雜質。
Three, clean the oil filter at the mouth of the filter, remove impurities attached to the filter.
四、對回油口處過濾網進行清洗,清除附著在過濾網上的雜質。註意事項有以下幾點:
Four, at the back of the oil filter at the mouth of the cleaning, removal of impurities attached to the filter. Note the following points:
1、將機件清洗再加以擦拭,請先確認無異物附著,再行安裝操作。
1, the machine cleaning and then wipe, please confirm that no foreign matter attached, and then install the operation.
彈簧機
2、隨時註意儲油槽油面高度,請勿讓油面過低,造成潤滑不良。
2, pay attention to the oil tank oil level height, do not let the oil surface is too low, resulting in poor lubrication.
五、打開儲油槽加油蓋,添加循環機油,讓儲油槽油面達到MAX位置,蓋上並旋緊儲油槽加油蓋,裝上回油管,開機後保持機械運行五分鐘,讓機器得到充分潤滑。
Five, open the gas tank cover, add circulating oil, let oil tank surface to MAX position, on the cover and tighten the oil tank filler cap, with the return pipe, after maintaining mechanical running five minutes, let the machine get sufficient lubrication.
本文文章來源:三级片在线观看更多的內容請進入: http://www.diannaothj.com我們的官方網站
This article source: spring machine more content please enter: http://www.diannaothj.com our official website

上壹篇:凸輪帶轉線萬能彈簧機的使用特性
下壹篇:選購無凸輪彈簧機要檢查伺服電機好壞
聯系我們
?