當前位置:首頁 - 新聞動態 > 公司公告 >

多功能電腦彈簧機在編程中容易出現哪些問題?

來源:http://www.diannaothj.com   時間:2019-04-03 17:30:41作者:山東銀豐彈簧機設備

當遇到裝置編程無法歸零的現象也缺乏為怪,主要的是檢查設備是不是處於正常狀態。消費彈簧的原理主要是應用反作用力,送線輪把鋼絲送向前方,在鋼絲前方用線規擋住,使鋼絲不能向前,產生阻力,改動鋼絲的運動方向,使鋼絲產生相關的外形。
When facing the phenomenon that device programming can not return to zero, it is not surprising that the main thing is to check whether the equipment is in normal condition. The principle of consumption spring is mainly to apply reaction force. The wire feeding wheel feeds the wire forward, and the wire gauge is used to block the wire in front of the wire, so that the wire can not move forward, produce resistance, change the moving direction of the wire, and make the wire have the relevant shape.
處置方法及步驟:
Disposal methods and procedures:
1。驅動器參數問題(這僅限於機械制造廠內部工作思索),若機器每次歸零後的零點位置均不在同壹點,則思索電子齒齡比設定能否正確。
1. Driver parameters (this is limited to the internal work of the mechanical factory), if the zero position of the machine after each return to zero is not at the same point, then consider whether the setting of electronic tooth age ratio is correct.
2。觀察多功用電腦彈簧機銀幕右上角的壹黃色三角信號燈能否有反向動作,觀察銀幕狀態。將作正常的歸零動作。若有,則可能為電路板損壞;若無反向動作,或做歸零動作時偶爾會反向,那就請翻開機器後蓋,重做歸零動作,觀察近接開關指示燈能否會在機器運轉壹周的過程中正常閃亮壹次。如不能正常閃亮,可將近接開關拿在手上,在機器歸零過程中,直接去與機器接觸,若近接開關為仍不亮,則檢查近接開關接在電路板上的插頭能否接觸不良,否則可判定近接開關本身缺點。
2. Observe whether a yellow triangular signal lamp in the upper right corner of the screen of the multi-function computer spring machine can move backwards and observe the state of the screen. Normal return to zero action will be performed. If yes, the circuit board may be damaged; if there is no reverse action, or if there is occasional reverse action when doing zero action, please open the back cover of the machine, do zero action again, and observe whether the proximity switch indicator will normally shine once in a week during the operation of the machine. If it can't shine normally, you can hold the proximity switch in your hand. In the process of returning to zero, you can contact the machine directly. If the proximity switch is still not bright, you can check whether the plug of the proximity switch connected to the circuit board is not in good contact, otherwise you can judge the shortcomings of the proximity switch itself.
電腦彈簧機
備註:
Remarks:
1。多功用電腦彈簧機運轉中,遏止用手接觸面板。彈簧產品的掉落壹定要控制好方向,以免卡住刀座,發作撞機現象,彈簧產品有異常時必需中止後才中止調整修正。
1. In the operation of the multi-function computer spring machine, the contact between the hand and the panel is prevented. The fall of spring products must be controlled in a good direction so as not to jam the tool holder and cause collision. When spring products are abnormal, they must be stopped before the adjustment and correction can be stopped.
2。彈簧消費設備的結構為主軸箱、電腦顯現屏,成型區,伺服電機,刀具,軸心,自動送線架,液壓區等。主軸箱及螺距區由伺服電機經過減速來帶動主軸轉動,或者縱向平移。
2. The structure of spring consumption equipment is spindle box, computer display screen, forming area, servo motor, cutter, axle center, automatic wire feeding frame, hydraulic area, etc. The spindle box and pitch area are driven by the servo motor through deceleration to rotate the spindle, or to move longitudinally.
3。由於多功用電腦彈簧機的原理不同於其他設備,操作時需求留意以下內容:開機要按嚴厲按運用步驟,消費前必需檢查調機時調動的壹切緊固件,以免在消費中松動、掉落、移位,發作撞機現象,招致機器損傷。
3. Because the principle of multi-function computer spring machine is different from other equipment, the following should be noticed when operating: Start the machine strictly according to the application steps, before consumption, it is necessary to check all fasteners mobilized during shunting, in order to avoid loosening, falling, shifting in consumption, occurrence of collision phenomenon, causing machine damage.

三级片在线观看電腦彈簧機的發展帶來的優勢特點
下壹篇:什麽樣的生產技術才能做出彈簧的觸指標準?
聯系我們
?